Buyers FAQs

We continually update our Frequently Asked Questions page to help you find the answer to your questions. If you are unable to find the answer to your question, please Contact Us.

TOP 3 BUYERS FAQS

HOW MUCH DOES IT COST TO RUN A LAY-Z-SPA HOT TUB?

We estimate it costs around £7 – £10 a week* to run a Lay-Z-Spa based on average usage. We are continually developing our hot tubs to be as cost efficient as possible – for example every Lay-Z-Spa pump now includes an Power Saving Timer.

The Lay-Z-Spa pump heater unit is thermostatically regulated, allowing it to intelligently heat the hot tub to save on running costs, much like a central heating system. The heater will heat the water to your desired temperature and then switch off. It will then switch back on again once it falls a few degrees below this.

Our Lay-Z-Spas also come with a top cover and an inflatable inner disc to provide maximum insulation. We have a thick Lay-Z-Spa Floor Protectoravailable as an accessory which provides added protection and insulation.

*This is based on feedback we have had from our customers (however is ONLY an estimate and does not take into consideration specifics such as electricity supplier and increase in frequency of usage). Figures are based the Vegas model, usage of 3 times a week for approx. 25 mins with 20 mins of Lay-Z-Massage including a 5 min interval. Wind-block and cover utilised.


WHAT EXTRAS DO I NEED?

Chemicals

When buying a Lay-Z-Spa you will not be required to purchase any additional tools or specialist equipment in order to erect the spa. We do however recommend you buy a Clearwater Chemical Spa Starter Kit which includes all the chemicals you need to get your spa running in no time. We also offer Hot Tub  Chemical Advice on our website for Clearwater products.

Accessories

We also have a range of Lay-Z-Spa Accessories available, from Drinks Holders and Floor Protectors to the Entertainment Station. For added protection and insulation for the base of your Lay-Z-Spa, we recommend the Lay-Z-Spa Floor Protector.


IS IT BEST TO LEAVE THE HEATER PUMP RUNNING ALL OF THE TIME OR TURN IT ON BEFORE USING IT?

In our experience is better to leave the heater activated, all of the time, if used regularly – say 3 or more times per week.


CHOOSING WHICH LAY-Z-SPA TO BUY

WHICH IS THE STRONGEST LAY-Z-SPA?

All our Lay-Z-Spas are composed using both a vertical and horizontal I-Beam Construction, offering superior structural stability without compromising on comfort. This durable configuration allows the spa to maintain its shape regardless of how many times it is inflated or deflated.

All materials used for our Lay-Z-Spas have been sourced with quality and comfort in mind. Each material used is highly durable and offers superior strength.

  • The Tritech material is exclusive to the Lay-Z-Spa range, and consists of a 3-ply reinforced material with a polyester mesh core that’s encased in 2 layers of laminated PVC. The inflated walls of the following spas use Tritech: Palm Springs Airjet, Hawaii Airjet, Siena Airjet, Palm Springs Hydrojet, Hawaii Hydrojet Pro.
  • The Leatheroid exterior cover provides complete protection and additional insulation to the spas. The exterior of the following spas have a Leatheroid cover: Paris Airjet, Vegas Airjet, Saint Tropez Airjet, New York Airjet.
  • The complexity of the Drop Stitch material is what gives the Monaco Airjet its rock hard rigidity. The Monaco Airjet is the only spa to feature this amazing material in its inflatable walls.
  • The Rayon Coating offers supreme protection to the outer walls of the spas, making them resistant from punctures. The exterior of the following spas have a Rayon Exterior Coating: Miami Airjet, Havana Airjet.

WHAT’S THE DIFFERENCE BETWEEN I-BEAM CONSTRUCTION AND CIRCULAR CONSTRUCTION?

Both constructions provide excellent stability. The internal welds of the I-Beam construction are vertical whereas that of the Circular Construction are horizontal. Our I-Beam construction range however includes a TriTech™ finish which means that the separate outer cover is not required. A TriTech™ finish also benefits from increased strength and durability.


HOW MANY PEOPLE CAN FIT IN A LAY-Z-SPA?

The number of people who can fit into a Lay-Z-Spa depends on which model you choose. A full breakdown of how many people can fit in each of our Lay-Z-Spa hot tubs can be found below.

Lay-Z-Spa Model Number of People
Miami 2-4
Havana 2-4
Vegas 2-6
Paris 4-6
Saint Tropez 4-6
New York 4-6
Palm Springs 4-6
Palm Springs HydroJet 4-6
Hawaii HydroJet 4-6
Hawaii 4-6
St Moritz 6-8
Siena 2
Monaco 4-6

WHAT IS THE AGE LIMIT FOR CHILDREN?

A Lay-Z-Spa is not a paddling pool or a toy and therefore is not suitable for children under 8 years old.


WHAT IS THE DIFFERENT BETWEEN THE HYDROJET, AIRJET AND HYDROJET PRO LAY-Z-SPA HOT TUBS?

AirJet™ Massage System: The AirJet™ massage system utilises a “massage seam” which is an extra air pocket that encircles the bottom of the spa. This will not inflate when the liner is inflated and instead is a material tube which includes tiny holes (this varies per Lay-Z-Spa).  When the bubble function is selected the pump pushes very high pressure air through this tube. The air escapes through the included holes causing the AirJet™ massage.

HydroJet™ Massage System: The HydroJet™ includes integrated jet nozzles in positions within the liner. When this function is turned on, the pump circulates a high-pressure combination of water and air which is then released through the jets. These jets can be adjusted in both direction and pressure.

HydroJet Pro™ Massage System: Lay-Z-Spas which include HydroJet Pro™ technology take advantage of both the HydroJet™ and AirJet™ massage systems. Both systems can be used simultaneously too provide a more vigorous massage.

For more information, read our blog.


DO ALL THE SPAS COME WITH A POWER SAVING TIMER FUNCTION?

All Lay-Z-Spa models released in 2017 and onwards come with the Power Saving Timer. This includes spare pumps which have been sold since 2017.


DO THE SPAS HAVE BUILT IN SEATS?

All Lay-Z-Spas include a cushioned floor which provides great comfort during periods of long use. The Lay-Z-Spa Maldives comes with built in seating and removable cushions. A padded Floor Protector can be purchased for additional padding.


I HAVE A BAD BACK AND/OR ARTHRITIS, IS THE SPA COMFORTABLE AND EASY TO GET IN AND OUT OF?

The cushioning in the base of the spa is suitable for periods of extended use. For those who suffer from arthritis or struggle to move, we recommend a Lay-Z-Spa Step and Surround  as they can provide extra assistance and support when entering and exiting the spa. Known as hydrotherapy, a Lay-Z-Spa helps relieve the effects of Arthritis by utilising the properties of warm water in order to facilitate the improved movement of joints which are stiff, ache or are painfully swollen. Find out more about how a Lay-Z-Spa helped arthritis sufferer Helen by reading our blog.


HOW LONG DOES A LAY-Z-SPA LAST?

If a Lay-Z-Spa is well maintained and cared for it can be enjoyed for many years to come. It is important that a Lay-Z-Spa is stored correctly and looked after throughout its life. For example it is recommended that a Lay-Z-Spa is not used in temperatures below 4°C as this can damage the pump and vinyl.


DO I NEED A FLAT SURFACE TO PLACE A LAY-Z-SPA?

Yes, a Lay-Z-Spa needs to be placed on a completely flat and solid surface.


HOW MUCH DOES A LAY-Z-SPA WEIGH WHEN FILLED (80%) WITH WATER?

Lay-Z-Spa Model Weight in Kilograms (Kgs) Weight in Pounds (lb)
Miami 696kg 1,534lb
Havana 696kg 1,534lb
Vegas 966kg 2,130lb
Paris 840kg 1,851lb
Saint Tropez 966kg 2,130lb
New York 840kg 1,851lb
Palm Springs 954kg 2,103lb
Palm Springs Hydro Jet 864kg 1,905lb
Hawaii HydroJet 867kg 1,911lb
Hawaii 879kg 1,938 lb
Siena 548kg 1,205lb
Monaco 1,973kg 4,349lb

HOW LOUD IS THE SPA WHEN IT IS IN OPERATION?

When a Lay-Z-Spa is set up in an open area 1 Meter away from the pump the decibel level is:

  • Filtration <60dB
  • Heating <60dB
  • Massage <72dB
  • Water Jet <72dB

CAN I ADD ACCESSORIES TO MY LAY-Z-SPA?

There are a huge variety of accessories to choose from for a Lay-Z-Spa. Including Pillows, Drinks Holders, Bluetooth Entertainment Station and Floor Protectors, you can customise a Lay-Z-Spa to suit your needs. Explore our Lay-Z-Spa Accessories and see what you could add to your spa.


GETTING YOUR LAY-Z-SPA DELIVERED

DO YOU DELIVER OUTSIDE THE UK?

To find out more about delivery outside the UK visit www.bestwaycorp.com to find your local stockists.


HOW LONG DOES IT TAKE TO DELIVER A LAY-Z-SPA?

Expected delivery is dependent on the type of delivery service selected at checkout as well as if the item is in stock or on pre-order. If the item is on pre-order there will be a delay in delivery corresponding to its stock arrival date. To find out more about our delivery prices and expected delivery times visit Delivery & Returns.


SETTING UP YOUR LAY-Z-SPA

HOW EASY IS THE LAY-Z-SPA TO SET UP?

Lay-Z-Spa hot tubs are inflated by using the supplied pump – this takes approximately 2 minutes. Please refer to your Instruction Manual for specific set up information or watch our handy Tutorial Videos.

From there all you need to do is fill the Lay-Z-Spa with fresh water, give it a commissioning shock dose of chlorine and wait for it to heat up! It is fine to fill the hot tub with warm water from the beginning if you wish. read our Chemicals Guide for more information and guidance.


WHERE IS THE BEST PLACE TO SET UP MY LAY-Z-SPA?

Suitable Surface: A smooth, flat, even surface that is capable of uniformly supporting the entire filled weight of your Lay-Z-Spa plus the weight of the users. Positioning your Lay-Z-Spa on an uneven surface can cause unequal pressure on one or other side of the hot tub which will increase the likelihood of your liner failing.

Power Supply: You need to consider having a power supply that is close enough for the cable to reach (approx. length of the cable is 7m) but also far enough away so that water cannot splash into the socket.

Surroundings: Also consider your surroundings: placing your Lay-Z-Spa near a wind break such as a fence will help to reduce wind exposure, helping it to retain more heat and in turn help to reduce your running costs. You should also consider where you will drain the water when required.


CAN I USE MY LAY-Z-SPA INDOORS AND OUTDOORS?

Lay-Z-Spa’s are suitable for use both outdoors and indoors. Whilst most of our customers set them up in their gardens either on a hard surface such as a patio or on their grass, a number of customers also set them up in a summer house, shed or garage. For use indoors, you should take particular time and care to consider factors such as drainage and ventilation.

When setting up a Lay-Z-Spa indoors or outdoors you should ask yourself the following questions:

  • For example, if there was a problem would water be able to drain freely without causing damage?
  • The Lay-Z-Spa is likely to increase the humidity of any confined space it is placed within, how would this affect the chosen area?
  • Have you fully considered the ventilation? Is the floor suitable to withstand the weight of the hot tub when full?
  • Is the floor a level non slip surface?
  • Does the electrical supply have an RCD?
  • Lay-Z-Spa does not take any responsibility or accept any liability for the use of the Lay-Z-Spa in an indoor area, summer house or garage.

HOW LONG DOES IT TAKE TO FILL?

Your Lay-Z-Spa will usually take approximately 1- 2 hours to fill up to the recommended line (depending on your water pressure and Lay-Z-Spa model).


HOW LONG DOES IT TAKE TO HEAT UP?

This can vary greatly depending on the temperature of fresh water that goes into the hot tub, the ambient air temperature and which Lay-Z-Spa model you have (the higher the capacity of water, the longer the hot tub will take to heat up).

The Lay-Z-Spa Pump heats the water via a circulating pump and heats up at approx. 1.5-2°C/h (3-4°F/h) per hour. In England in the Summer, it can take on average 6 – 12 hours. Ensuring that the spa is well insulated and that the Lid is on will also greatly help!


MAINTAINING YOUR LAY-Z-SPA:

IS A LAY-Z-SPA EASY TO CLEAN & MAINTAIN?

The Lay-Z-Spa range of inflatable hot tubs are very easy to maintain and are all supplied with an owner’s manual with maintenance instructions to help you get the best from your purchase.


HOW MUCH WILL IT COST TO MAINTAIN AND RUN AN INFLATABLE HOT TUB?

We estimate it can cost around *£7 – £10 a week to run based on feedback we have had from our customers (this however is ONLY an estimate and does not take into consideration specifics such as electricity supplier and increase in frequency of usage).

Our Lay-Z-Spas come with a top cover and an inflatable inner disc to provide additional insulation and we also have floor protectors, which can all reduce running costs of an inflatable spa.

As the Lay-Z-Spa heater is thermostatically regulated, the heater will only actually switch on to top up the temperature of the water to your desired temperature, once it falls a degree or two below this.

*Figures based Spa usage of 3 times a week for approx 25 mins with 20 mins of Lay-Z-Massage including a 5 min interval. Wind-block and cover utilised.


CAN YOU LEAVE THE PUMP RUNNING ALL THE TIME?

We recommend leaving the pump on all the time, as this maintains the heat of the water and will ensure the filter is constantly filtering the spa’s water.


CAN THE HEAT AND AIRJET™ MASSAGE SYSTEM STAY ON AT THE SAME TIME?

Yes, Lay-Z-Spa’s with a 2017 or newer pump can heat and use the AirJet™ Massage System at the same time.


CAN THE HEAT AND HYDROJET™ MASSAGE SYSTEM STAY ON AT THE SAME TIME?

No, Lay-Z-Spa’s with a 2017 or newer pump cannot heat and use the HydroJet™ Massage System at the same time. Heating can only be on at the same time as the AirJet™ Massage System.


WHAT SHOULD I DO WITH MY LAY-Z-SPA IF I AM GOING ON HOLIDAY? SHOULD I LEAVE THE FILTER RUNNING ALL THE TIME?

If it’s only for a few days, the pump, filter and heater can be left running. If you will be away more than 72 hours the pump unit will switch itself off due to the inbuilt Power Saving Timer. The water needs to be continuously circulated so it would be advisable to arrange for someone to go in and reactivate it. Otherwise, we would advise that you drain and clean down your Lay-Z-Spa, and re fill it when you return.


DOES THE SPA NEED CONSTANT POWER TO STAY INFLATED?

No, a Lay-Z-Spa does not require the pump to be on constantly to be kept inflated. The pump can be used however at initial setup to inflate the spa in 1 to 2 minutes.


IS IT EASY TO DRAIN THE SPA? HOW LONG DOES IT TAKE?

Draining a Lay-Z-Spa is a simple and easy process. Simply screw on the stopper caps to the inside of the spa and remove the pump. Then use the drain adapter to attach a hose pipe to the spa to allow for the drainage of the majority of the spa’s water. Any remaining water can then be tipped out from the spa. Alternatively a Pool and Drain Pump  can be used to extract the water.


HOW LONG DO FILTERS LAST?

The lifetime of a filter varies according to their maintenance regime and water conditions. A Filter should be cleaned after every use or at least every other day. However ‘hard’ water can result in an increased build-up of lime scale and therefore can result in increased cleaning and replacement of a filter cartridge. This can be alleviated however with Clearwater Scale and Stain Remover.


CAN I LEAVE MY SPA IN DIRECT SUNLIGHT?

No, a Lay-Z-Spa should not be left in direct sunlight as this can cause damage to its liner.


CAN I ADD MORE AIR TO THE SPA WHEN IT IS FULL OF WATER?

Yes. To do so simply apply Stopper Caps to the inside of spa to prevent water loss. You should then remove the pump and add a stopper to ‘A’. You can then add air to the spa in the same way as when you initially inflated the spa.


IS IT EASY TO GET ACCESSORIES AND SPARE PARTS?

Yes, you can order Spare Parts and Accessories  directly from Lay-Z-Spa.


ELECTRICITY & SAFETY WITH YOUR LAY-Z-SPA:

WHAT ELECTRICITY SUPPLY DO I NEED TO RUN MY LAY-Z-SPA?

Our hot tubs run on a UK standard 13amp/240V electrical supply. You should always use a grounded socket with RCD protection. All of our pumps come with a built in RCD unit as a safety measure. The socket that the hot tub is being plugged in to should be grounded and at least 4 metres away, at a height of at least 1.2m from the ground. We recommend getting a qualified electrician to install a grounded outdoor waterproof socket with RCD protection (this should always be done by a qualified electrician).


CAN I USE AN EXTENSION LEAD?

No, extension cables cannot be used with Lay-Z-Spas. The Lay-Z-Spa pumps come with a 7 metre cable which is usually sufficient for customers to reach their nearest grounded socket with RCD protection. If the cable is not long enough, we recommend getting a qualified electrician to install a grounded outdoor socket with RCD protection. The socket that the hot tub is being plugged in to should be grounded and at least 4 metres away, at a height of at least 1.2m from the ground.


WHAT IS AN RCD?

All of our spas are fitted with an internal RCD (residual-current device) this is a cut-out device in the event that water comes into contact with the electrical supply to your inflatable hot tub.


IS THE PUMP AND RCD WATERPROOF?

Yes, however the pump should not be left sat in deep puddles of water. The PRCD is water proof to IPX5 and therefore should not be submerged.


CHEMICALS, WATER HEALTH & YOUR LAY-Z-SPA:

HOW DO I MAINTAIN MY LAY-Z-SPA WATER ON A DAILY BASIS?

In order to maintain clear, clean and healthy water there are some day-to-day / regular tasks that you will need to undertake:

1. Water Filtration / Circulation

It is a combination of circulating the water through the filter cartridge to collect suspended dirt and oils, together with good chemical water treatment that helps you to maintain clear, clean and healthy water.

Whenever the Lay-Z-Spa’s heater is turned on, the filtration function is automatically activated. If you wish, it is possible to activate the filter on its own, to keep the water circulating but not heating.

2. Water Testing & Daily Adjusting of Chlorine & pH Levels

It is essential to test the water every time before getting in. Chemicals will still get used up and will be constantly changing, even if you haven’t used the spa. We recommend testing the water 1-2 hours before you plan to use it to give you time to make any chemical adjustments if required.

When it comes to water testing we recommend using Clearwater Dip Test Strips. Using Clearwater 3 Way Dip Test Strips you are able to quickly and accurately assess your spas water conditions and make adjustments to the chemical levels as required:

      1. Free Chlorine
      2. pH Levels
      3. Total Alkalinity (TA)

Test Ideal Reading Description Solution
Free Chlorine 3-5 ppm* This refers to the amount of chlorine in your spa that can sanitize or disinfect the water, keeping it safe for users.

It is safe to bathe in the water when the chlorine level is 5ppm or less (ideal level is 3-5ppm).

Too little chlorine results in cloudy water and insufficient sanitization, providing a breeding ground for algae and bacteria which may be hazardous to health.

Too much chlorine may result in skin and eye irritation.

Clearwater Chlorine Granules

 

Clearwater Mini Multifunction Tablets

pH level 7.2 – 7.6 pH is a measure of the acidity or alkalinity of your spa water.

The pH of spa water tends to increase during use, eventually becoming too alkaline. This results in formation of scale, cloudy water, skin and eye irritation and causes chlorine to be lost through evaporation.

Alternatively the pH level of your spa water may drop below the recommended range, becoming too acidic. This may result in corrosion, skin and eye irritation and reduces the sanitizer efficiency of chlorine.

Clearwater pH Minus to decrease

 

Clearwater pH Plus to increase

 

Total Alkalinity 80 – 160 ppm* The total alkalinity (TA) is a measure of the capacity of your spa water to neutralize the water when it becomes too acidic.

When the total alkalinity is within this recommended range, it prevents rapid changes in the pH of your water.

If the TA is too low the pH will become unstable and increase or decrease rapidly. If the TA is too high, the pH of your water will become difficult to adjust, the water becomes cloudy and chlorine treatment will be less effective.

This is unlikely to fall outside of the normal parameters.

If you do find that the TA is too high, take out some of the pool water and replace with fresh water, continuing until a normal TA reading is achieved.

If TA is too low, add small increments of pH increaser.


HOW OFTEN DO I NEED TO CHANGE THE WATER?

This really varies depending on how effective you are at maintaining your water using a chemical maintenance regime.

It is recommended that Lay-Z-Spa water is changed regularly, and at least once per month. The frequency of water changes should reflect the degree of use of the pool, as well as the results of chemical testing. If chemical levels have fallen far outside the normal ranges, it is recommended that the water is completely replaced and re-treated.

It is important to shock dose your water on a regular basis and you will find it will extend how long you can use the water for.


DO I NEED TO USE CHEMICALS AND WHY?

Yes, regardless of how often or long you plan to use your hot tub, it is essential to treat the water in your Lay-Z-Spa using Chemicals. If you left your Lay-Z-Spa water without any treatment, it would soon become uncomfortable, unclean and potentially dangerous even just to passers-by.

Chemicals are a highly effective way to treat your Lay-Z-Spa, as they eliminate any harmful bacteria that can grow in warm water. (It doesn’t take long to get used understanding and using chemicals in your Lay-Z-Spa. Before long it will become second nature to you.)


DO I HAVE TO USE CHLORINE IN MY LAY-Z-SPA?

Chlorine or bromine is a powerful sanitiser which is necessary to keep your hot tub clean and healthy. As a body of still water, a hot tub runs the risk of becoming stagnant and dangerous if not treated properly. Therefore it is essential to use ClearWater Chemicals to help maintain the water health of your spa.


WHAT ARE THE RECOMMENDED CHEMICALS & ACCESSORIES FOR LAY-Z-SPA HOT TUBS?

Chemical or Accessory: FORM FUNCTION
Clearwater Chlorine Granules Granules Clearwater Chlorine Granules are one of our most popular products and are widely considered an essential item in every hot tub owner’s tool kit.

Chlorine granules disinfect the spa water by killing bacteria which builds up in your Lay-Z-Spa. They are quick dissolving and relatively pH neutral.

For more information visit one of the product pages below, all of which include Clearwater Chlorine Granules:

· Clearwater 1KG Chlorine Granules >

· Clearwater 5KG Chlorine Granules >

· Spa Chemical Starter Kit >

Clearwater Dip Test Strips Strip Clearwater Dip Test Strips are a quick, easy but essential way to check the chlorine, pH and alkalinity levels of your spa water, allowing you to provide it with the right treatment if necessary. Untested water can develop a chemical imbalance which may result in an unhygienic swimming environment or skin irritations.

Simply dip a test strip into your hot tub water, quickly remove it and allow the colour to develop. The results can be checked against the colour chart provided, indicating each level.

The following levels are recommended:

· Chlorine: 3 – 5 ppm

· pH: 7.2 – 7.6

· Total Alkalinity: 80 – 120 ppm depending on the chemical treatment

Checking these levels allows you to identify what chemical treatment your spa water requires to bring it back within the recommended range.

For more information, please visit the product pages below, which include dip test strips:

· Clearwater Dip Test Strips x 25 >

· Clearwater Spa Chemical Starter Kit >

Clearwater Mini Multifunction Tablets Tablet Clearwater Mini Multifunctional Tablets are an effective and hassle-free way of maintaining clear and healthy spa water. They contain a combination of chemicals that act in a number of ways.

These slow release tablets contain:

· Chlorine – which kills bacteria by disinfecting water

· Algaecide – which kills algae even before it becomes visible to the naked eye

· Water Clarifier – which contains flocculants that binds debris and particles together ensuring adequate filtration, resulting in clean and sparkly water

The Bestway 5in Chemical Floater is the designed for use with this product. The chemical dispenser slowly releases the mini tablets into the water, making this a completely hassle-free way of treating your water even for the user with a busy schedule.

For more information, please visit the product pages below:

· Clearwater Mini Multifunctional Tablets >

· Bestway 5 inch Floating Chemical Dispenser >

· Lay-Z-Spa Gold Spa Starter Kit >

· Lay-Z-Spa Ultimate Spa Starter Kit >

Bestway 5 inch Chemical Floater Chemical Tablet Dispenser The Bestway 5 Inch Chemical Floater slowly releases Clearwater Mini Multifunctional Tablets or Chlorine Tablets, making it the perfect accessory for busy spa users who want a hassle free way of maintaining clear and healthy spa water.

The dispenser has an adjustable dial which controls the release of the 20g tablets, ensuring that the sanitizer level of your spa water is consistently and efficiently maintained.

For more information, please visit the product pages below:

· Bestway 5 inch Floating Chemical Dispenser >

· Clearwater Mini Multifunctional Tablets >

Clearwater pH Plus Granules Clearwater pH Plus, also known as ‘pH increaser’ is the best way to increase pH levels that have dropped below the recommended level.

To avoid skin discomforts and enable the chlorine in your spa to work effectively, it’s vital that acidity is monitored and controlled.

The recommended pH balance of spa water is between 7.2 and 7.6.

For more information visit one of the product pages below, all of which include Clearwater pH Plus:

· Clearwater Spa Chemical Starter Kit (includes pH Plus) >

· Clear Water 1KG pH Plus Increaser >

Clearwater pH Minus Granules Clearwater pH Minus, also known as ‘pH reducer’ is the most simple and effective way to decrease the pH of your spa water when it has surpassed the recommended level.

When the pH of water increases above 7.6 pH treatment is required to reduce the alkalinity, in order to prevent skin discomfort and allow the chlorine in your spa to work more effectively.

For more information, please visit one of the product pages below which include Clearwater pH Minus:

· Clearwater Spa Chemical Starter Kit (includes pH Plus) >

· Clearwater 1.5KG pH Minus Decreaser >

Clearwater Clarifier Liquid Clearwater Clarifier contains flocculants which bind small particles of debris and algae together so that your Lay-Z-Spa filtration system can adequately remove them, resulting in clean and sparkly water.

This is a very effective way of preventing your spa water from looking dull and cloudy, due to the build-up of dead algae and debris that is too small to be trapped by your filter.

Even if you have treated your spa for algae using Clearwater Algaecide, it is recommended that you use the Water Clarifier to remove any residual debris.

For more information, please visit the product page below:

· Clearwater 1 Litre Clarifier >

Clearwater Algaecide Liquid Clearwater Algaecide is the quickest and most effective way to eliminate and prevent the build-up of algae, which provides an ideal breeding ground for germs and bacteria.

If algae forms on or below the surface of your water, simply pour the recommended dose of algaecide into your spa near the water inlets so that it is distributed evenly throughout the water. Regular application is recommended to control growth and maintain a clean and hygienic environment.

For more information, please visit the product page below:

· Clearwater 1 Litre Algaecide >

Clearwater Foam Remover Liquid Clearwater Foam Remover is designed to control and prevent foaming in your hot tub, which is typically caused by the reaction of water with shampoos, deodorants and natural body oils present on the user.

The Clearwater Foam Remover will tackle foaming regardless of its cause, returning your water to its crystal clear appearance.

For more information, please visit the product page below:

· Clearwater 1 Litre Foam Remover >

· Clearwater Spa Chemical Starter Kit >


THE WEATHER & YOUR LAY-Z-SPA:

CAN I USE MY LAY-Z-SPA IN THE WINTER?

The Lay-Z-Spa should not be setup or left out in temperatures lower than 4°C (40F). However a hot tub in the winter is every bit as enjoyable if not better on a cold crisp starry evening. So if you wish to use your hot tub in winter always make sure it is protected either on a raised platform in a sheltered or covered area and remember ambient temperature should be regularly checked so that it does not fall below 4°C (40F) as water could freeze within the pump and cause irreparable pump failure. For more information on looking after your spa in winter read our blog.


IS THE PUMP WATERPROOF AND CAN THE PUMP BE COVERED AND LEFT OUT ALL YEAR ROUND? 

Yes a Lay-Z-Spa pump is water proof, however if you are expecting a very large amount of rain or bad weather it is recommended that you bring the spa and pump indoors. Constant adverse weather conditions could damage the spa and pump and they should not be used in temperatures below 4°C.


HOW DO I STORE MY LAY-Z-SPA IN THE WINTER?

Simply drain, deflate, clean thoroughly with a mild non-abrasive cleaner, rinse thoroughly, dry and all should go back into the box for storage. Please store the Lay-Z-Spa in a dry, moisture free environment that has an ambient temperature of well above 4ºC.


SUPPORT & WARRANTY

WHAT HAPPENS IF I HAVE A QUESTION OR ISSUE WITH MY LAY-Z-SPA?

We have a UK based Aftersales team, dedicated to answering any Lay-Z-Spa enquiries that you may have. We also have a comprehensive online advice and troubleshooting area that will help guide you through any issues or queries you may have.


HOW LONG IS THE WARRANTY ON A LAY-Z-SPA?

Please visit our dedicated Warranties Page for more details.


WHAT IF MY HOT TUB GETS A PUNCTURE?

Our hot tubs are manufactured from the toughest reinforced spa material you can find, however accidents do happen and with this in mind we always include a repair kit with your inflatable spa purchase. You can also buy spare pumps, covers  and liners  from our website.


DO YOU SELL INTERNAL PARTS FOR THE PUMP?

No. Due to the combination of water and electricity the spa pumps are not deemed to be user serviceable.

If you still not any help or advice before purchasing please Contact Us